Extron MTP T 15HD A MTP Twisted Pair VGA Audio Transmitter w/ Pre Peak

Not rated yet
0
  • $35.00
 
In stock(1 item available)
OR
Extron MTP AV Transmitter
 SPARES - REPAIRS - UPGRADES

GENUINE OEM Extron
Model MTP T 15HD A
Includes OEM Extron Power Supply

NO Better & Best Supported - Get Extron !

 Get A GOOD One !
Save $$$ right here at GetThatPart

 
CALL US with questions - Our business line is 410-374-1261

About This Item
Actual item from lot is shown. Only what is shown is included. TESTED Unit - pulled from working system and cleaned, inspected, and recertified for dependable daily use by our tech team. Unit was tested prior to parts harvest and determined to be working perfectly. See pictures - also includes oem Extrom power supply. Guaranteed functional for a period of 30 days.

Know What You are Buying

  • We typically take the time to post actual pictures of the unit you are buying
  • We also typically take the time to thoroughly test the units we are selling
  • Buy with CONFIDENCE from a reputable seller with 20 Years experience

DESCRIPTION

Manufacturer - Extron
Part # MTP T 15HD A / MTP-T-15HD-A  / MTPT15HDA
 
The Extron MTP T 15HD A Twisted Pair Transmitter with EDID Minder® sends high resolution video and audio signals to a compatible MTP receiver. The MTP T 15HD A  features EDID Minder, which automatically manages EDID communication to ensure that the source powers up properly and reliably outputs content for display. It accepts computer-video, HD and standard definition video, and audio inputs on female 15-pin HD connectors and 3.5 mm stereo audio jacks. The video and summed mono audio signals are transmitted over a single CAT 5-type cable to a compatible twisted pair receiver. The MTP T 15HD A also features a local monitor output for systems that require a local display.
 
Key Features
  • Transmits high resolution video and summed mono audio signals over a single CAT 5-type cable
  • EDID Minder® automatically manages EDID communication between connected devices
  • Supports RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, and composite video
  • Compatible with HDTV component video, bi-level or tri-level sync
  • Pre-peaking circuit for optimizing video signal on long cable runs
  • Rack-mountable, 1U, quarter rack width metal enclosure
General
Control/remote — external device (pass-through, unidirectional or bidirectional) — MTP R 15HD RSA D only
Audio output — receivers
Audio output — MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM local stereo output
Audio input — transmitters
Audio — all models
Sync
Video output — receivers (MTP RL 15HD A, MTP RL 15HD A SEQ, MTP R 15HD RSA D, MTP 1500RL 15HD A SEQ. MTP C7 RL 15HD A)
Video input and loop through — transmitters
Video
MTP 15HD A Series Combo
 
   Gain Unity
   Number/signal type 1 set of proprietary analog signals
   Connectors  
      MTP R 15HD RSA D 1 female RJ-45 on a pigtail
      All other models 1 female RJ-45
 
   Number/signal type  
      MTP T 15HD A, MTP C7 T 15HD A 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits)
      MTP T 15HD A AAP, MTP T 15HD A D, MTP T 15HD A WM 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video
   Connectors  
      MTP T 15HD A, MTP C7 T 15HD A 2 female 15-pin HD
      All other transmitters 1 female 15-pin HD
   Nominal level 1 Vp-p for Y of component video and
S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
   Minimum/maximum levels 0.3 V to 1.45 Vp-p
   Impedance 75 ohms
   Horizontal frequency 15 kHz to 130 kHz
   Vertical frequency 30 Hz to 150 Hz
   Return loss <-30 dB @ 5 MHz
   DC offset (max. allowable) 250 mV
 
   Number/signal type  
      MTP R 15HD RSA D 1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video
      All other receivers 1 set of proprietary analog signals
1 analog RGBHV, RGBS, RGsB, RsGsBs, component video (bi-/tri-level sync), S-video, or composite video
   Connectors  
      MTP R 15HD RSA D 1 female 15-pin HD
      All other receivers 1 female RJ-45
1 female 15-pin HD
   Nominal level 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB and for R-Y and B-Y of component video
0.3 Vp-p for C of S-video
   Minimum/maximum levels 0.3 V to 1.45 Vp-p
   Impedance 75 ohms
   Return loss <-30 dB @ 5 MHz
   DC offset  
      MTP R 15HD RSA D <±20 mV with input at 0 offset
      All other receivers <±35 mV with input at 0 offset
   Skew compensation 62 ns
   Maximum resolution  
      MTP 1500RL 15HD A SEQ Up to 1600x1200 and 1080p at 1500'
Up to 1920x1200 and 2048x1080 at 1200'
      All other models Up to 1920x1200 or 2048x1080 or 1080p at 300'
Up to 1024x768 at 600'
    NOTE     See the user guide for the maximum distances recommended for specific resolutions. 
 
   Input type (transmitters) RGBHV, RGBS, RGsB, RsGsBs
   Output type (receivers) RGBHV, RGBS, RGsB, RsGsBs
   Standards NTSC 3.58, NTSC 4.43, PAL, SECAM
   Input level (transmitter) 3.5 V to 5.5 Vp-p, unterminated
   Output level (receivers) 4.0 V to 5.0 Vp-p, unterminated
   Input impedance (transmitter) 573 ohms ±5%
   Output impedance (receivers)  
      MTP C7 15HD models 92 ohms ±8% (25 mA)
      All other models 110 ohms
   Polarity  
      Transmitter Positive or negative (follows input polarity)
      Receivers Positive or negative (switch-selectable)
 
   Number/signal type 1 set of proprietary analog signals
   Connectors 1 female RJ-45
   Gain Unbalanced output: 0 dB; balanced output: +6 dB
   Frequency response 20 Hz to 20 kHz, ±1 dB
   THD + Noise 0.15% @ 1 kHz, 0.3% @ 20 kHz at nominal level
   S/N >70 dB at maximum output (unweighted)
   Stereo channel separation >60 dB @ 1 kHz
   CMRR >43 dB @ 20 Hz to 20 kHz
 
   Number/signal type 1 stereo, unbalanced
   Connectors (1) 3.5 mm mini stereo jack
   Impedance >10k ohms, unbalanced
   Nominal level +4 dBu (1.23 Vrms), -10 dBV
(316 mVrms)
   Maximum level  
      MTP C7 15HD models +12 dBu, (unbalanced) at 1%THD+N
      All other models +18 dBu, (unbalanced) at 1%THD+N
    NOTE     0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu 
 
   Number/signal type 1 stereo, balanced/unbalanced
   Connectors (1) 3.5 mm direct insertion captive screw connector, 5 pole
   Impedance 50 ohms unbalanced, 100 ohms balanced
   Gain error ±1 dB channel to channel
   Maximum level (Hi-Z) >+23 dBu, balanced or unbalanced at 1% THD+N
   Maximum level (600 ohm) >+17 dBm, balanced or unbalanced at 1% THD+N
 
   Number/signal type  
      MTP R 15HD RSA D 1 mono, balanced/unbalanced
      All other receivers 2 mono, balanced/unbalanced
   Connectors  
      MTP R 15HD RSA D (1) 3.5 mm captive screw connector, 5 pole (uses 3 poles)
      All other receivers (1) 3.5 mm captive screw connector, 5 pole
   Impedance 50 ohms unbalanced, 100 ohms balanced
   Gain error ±1 dB channel to channel
   Nominal level +4 dBu (1.23 Vrms), -10 dBV (316 mVrms)
   Maximum level  
      MTP R 15HD RSA D 14 dBm, unbalanced at 1% THD+N
      All other receivers +18 dBu, unbalanced at 1% THD+N
 
   Serial control port input/output 1 set of proprietary signals on a female RJ-45 jack
   Serial control port output/input RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole
   Baud rates Up to 38400 bps at up to 600' (182.9 m)  (Higher data rates and distances are possible.  Performance varies based on baud rate and cable length.)
   Protocol Data bits = 5 - 8
Stop bits = 1 or 2
Parity = odd, even, none
Flow control = XON, XOFF, none
    NOTE     Protocol is mirrored between the transmitter and the receiver. 
   Serial control pin configuration Captive screw connector: 1 = Tx, 2 = Rx,
3 = GND
 
   Recommended cable type  
      Models other than C7 models CAT 5/5e/6 (shielded or unshielded)
   Required cable type  
      MTP C7 15HD models Extron STP201 or CAT 7
   Power supply External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1 A, 12 watts
   Power input requirements  
      MTP 1500RL 15HD A SEQ 12 VDC, 1 A
      All other models 12 VDC, 0.5 A
   Temperature/humidity Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
   Cooling  
      MTP 1500RL 15HD A SEQ Convection, vents sides to top
      All other models Convection, no vents
   Mounting  
      Rack mount  
         MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ, MTP 1500RL 15HD A SEQ Yes, with optional 1U rack shelf
      Furniture or wall mount  
         MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ Yes, with optional under-desk mounting kit
         MTP T 15HD A AAP Yes, with optional AAP mounting faceplates that have double space high AAP opening
         MTP T 15HD A D, MTP R 15HD RSA D Yes, in a decorator-style opening with a standard electrical wall box or decorator-style size mud ring
         MTP T 15HD A WM Yes, in a 1-gang opening
      Wall mount  
         MTP 1500RL 15HD models Yes, with optional wall mounting kit
      Pole mount  
         MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ Yes, with optional pole mounting kit
   Enclosure type Metal
   Enclosure dimensions  
      MTP T 15HD A, MTP RL 15HD A, MTP RL 15HD A SEQ 1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide)
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.)
      MTP C7 15HD models 1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide)
(4.3 cm H x 10.9 cm W x 7.6 cm D)
(Depth excludes connectors and knobs.)
      MTP 1500RL 15HD SEQ models 1.0" H x 8.75" W x 6.0" D (half rack wide)
(2.5 cm H x 22.2 cm W x 15.2 cm D)
(Depth excludes connectors.)
      Faceplates  
         MTP T 15HD A AAP 1.4" H x 3.5" W x 0.1" D (3.6 cm H x 8.9 cm W x 0.3 cm D)
(double space high AAP plate)
         MTP T 15HD A D, MTP R 15HD RSA D 2.6" H* x 1.3" W x 0.1" D (6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang, 4.4" H x 2.7" W
decorator-style wallplate. Depth excludes connectors.)
*Overall height is 4.1" (10.4 cm) including mounting tabs.
         MTP T 15HD A WM 4.5" H x 2.8" W x 0.1" D
(11.4 cm H x 7.1 cm W x 0.3 cm D)
(1 gang)
      Device  
         MTP R 15HD RSA D 2.75" H x 1.65" W x 1.3" D
(7.0 cm H x 4.2 cm W x 3.3 cm D)
(Depth excludes connectors.)
         Other AAP, D, and WM models 2.7" H x 1.4" W x 1.4" D
(6.9 cm H x 3.6 cm W x 3.6 cm D)
(Depth excludes connectors.)
   Product weight  
      MTP 1500RL 15HD A SEQ 1 lb (0.5 kg)
      All other models 0.4 lbs (0.2 kg)
   Vibration ISTA 1A in carton (International Safe Transit Association)
   Regulatory compliance  
      Safety CE, c-UL, UL
      EMI/EMC CE, C-tick, FCC Class A, ICES, VCCI
   Product warranty 3 years parts and labor
   Everlast power supply warranty 7 years parts and labor
    NOTE     All nominal levels are at ±10%. 
    NOTE     Specifications are subject to change without notice. 
(CMS-041917-D18)
Shipping Dimensions and Weights
    Part #HeightWidthDepthWeight
    60-1282-012.88" (7.3 cm)7.31" (18.6 cm)10.44" (26.5 cm)1.82 lbs (0.83 kg)

 

 
CALL US with questions - Our business line is 410-374-1261

 

Thanks for looking!
    • SKU
      SKU100728
    • Weight
      3.0000 lbs
    • Dimensions (L x W x H)
      9 x 4 x 6 in
  • Manufacturer
    EXTRON
  • Product Added Date
    5/14/2019
  • Inventory Added Date
    5/14/2019
  • Condition Code
    Refubished
  • Bin Location
    SRP18
  • P/N
    MTP T 15HD A
  • BB Condition Code
    Ref
  • Local Inventory
    1
Customer reviews
There are no comments yet. Be the first to leave a comment
Please sign in to add review

Footer navigation