Dahle 20634 EC MicroCut Steel Gear Industrial German Paper Shredder

Not rated yet
0
  • $495.00
Out of stock
PERFECT WORKGROUP BUSINESS SECURITY SHREDDER
All Steel Gear Drive - Motor to Reducer to Chain Drive Machine
(No Plastic gears to fail - Built to last a lifetime)

Dahle 20634 Security MicroCut Shredder

Check underthehood - actual pics attached !
Awesome never fail drivetrain / gears
(No one else shows you "under the hood" pictures)
 
Includes Electronic Controls Option (EC)
(Heavy Relay Starts via Soft Switch)
 
Dahle = Quiet by Design
Rubber isolation mounts & engineered to minimize noise

UNMATCHED German Made Machine
HI-CAPACITY - APPX 156 SHEETS/ MIN
HEAVY 1.25 HP ENGINE - DURABLE/RELIABLE

Rated to 9,360 Sheets per hour!
 
Reconditioned by an AUTHORIZED HSM Dealer
Buy from experts who can answer all your questions - not a sales person
GUARANTEE - EXPERTISE - SUPPORT & SUPPLIES (oil, too)
 

CALL US with questions - Our business line is 410-374-1261

About This Item
Actual item is shown. Only what is shown is included. Used unit reconditioned thoroughly in our factory shop and performing to new oem specs. Pictures are of actual unit, so please review pictures for detail on condition and interfaces. The machine was operated in all modes and found to grind paper per specifications. The result is shown in the pictures. This unit is designed for commercial duty applications. We guarantee this machine to perform as we have described upon receipt.

Notes from our Tech when ReConditioned
This is an advanced German designed and made microshred machine. It will be impossible for any shreds to be reconstructed. We ran several hundred pages through it after going through our shop, with no issues whatsoever. The machine was load tested and found to pass the spec 6 sheets per pass - constantly (per new spec). The sensors were performance tested and all work as intended. The machine was fully cleaned and lubed. All drivetrain components checked for wear. The mill and all components performing per oem specification. The case will show some blemishes consistent with use of a machine of this type and we have pictured those blemishes.

Serial No - DT 00302

Machine ID - 81.11.20634


MPN -20634 EC

Level 6 MicroShredder
This is one of the highest throughput Level 6 (guaranteed audible NSA 0201 machine) machines in it's class (1.25 HP). If you have security requirements - this machine is a set it and forget it solution.

NSA One Hour Durability Rating Certification - Rated by the NSA at 10 reams / 3 sheets per pass

 
Know What You are Buying

  • We typically take the time to post actual pictures of the unit you are buying
  • We also typically take the time to thoroughly test the units we are selling
  • Buy with CONFIDENCE from a reputable seller with 20 Years experience

WARRANTY - BUYER will enjoy a full performance warranty for 180 days. We will replace defective components or refund / exchange the machine if it fails to operate as we have described for a period of 180 days in accordance with our terms in our guarantees section below.

Specifications

Maximum Particle Area: 
Ninety percent (90%) of the shredded particles shall not exceed five square millimeters (5 mm²).

  Maximum Particle Width: Seventy five percent (75%) of the shredded particles shall have no edge dimension exceeding five millimeters (5mm) in length.

  Durability: Shredder shall operate continuously for one (1) hour, shredding paper at a feed rate prescribed by the manufacturer, and consistently produce particles that meet specification requirements.

Features

  • The Dahle 20634EC High Security Shredder is NSA/CSS 02-01 approved for the shredding of confidential government documents.
  • Ideal for small offices and military, federal, state or local departments as well as department of defense contractors.
  • Shreds up to 8 sheets of paper at speeds up to 26' per minute.
  • Cross-cuts documents into 1mm x 4.7mm particles.
  • Every sheet becomes 15,500 tiny particles.
  • 16 gallon waste bin.
  • Automatic on/off, reverse, and bag full auto off.
  • 10" wide feed opening.
  • Powered by a 1 horsepower motor.
  • Chain driven to provide slip free power while shredding.

Specifications

Shred Specifications
 Model 20634
 Shred Size (Width) 3/64"
 Shred Size (Length) 5/32"
 Sheet Capacity Up to 6 sheets
 Speed 26 feet per minute
 Shred Type Government Use
 Throat Size 10"
 Waste Container Volume 16 gallons
 Product Dimensions (H x W x D) 30 1/2" x 16 3/4" x 15 3/4"
 Auto On/Off Yes
 Auto Reverse Yes
 Bag Full Indicator Yes
 Continuous Duty Motor Yes
 Horse Power 1
 Voltage 115
 Shipping Weight 125 lbs

 

CALL US WITH ANY QUESTIONS - OUR BUSINESS LINE IS 410-374-1261


Thanks for looking!
    • SKU
      SKU103185
    • Weight
      145.0000 lbs
    • Dimensions (L x W x H)
      40 x 30 x 36 in
  • Manufacturer
    DAHLE
  • Product Added Date
    4/5/2012
  • Inventory Subtract Date
    4/21/2020
  • Inventory Added Date
    4/7/2019
  • Condition Code
    Refurbished
  • Bin Location
    OB-R3
  • P/N
    20634 EC
  • BB Condition Code
    Ref
Customer reviews
There are no comments yet. Be the first to leave a comment
Please sign in to add review

Footer navigation